 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HEP801 THRU HEP806 Features * Plastic package has Underwriters Laboratory Flammability Classification 94V-0 * Low forward voltage drop * High current capability * High reliability * Low power loss, high effciency * High surge current capability * High speed switching * Low leakage 3.7 0.2 CURRENT 8.0 Amperes VOLTAGE 50 to 600 Volts ITO-220A 10 0.5 3.2 6.4 0.1 4.5 0.2 2.7 2.7 0.2 Mechanical Data * Case : JEDEC ITO-220A molded plastic body * Terminals : Lead solderable per MIL-STD-750, method 2026 * Polarity : As marked * Mounting Position : Any * Weight : 0.08 ounce, 2.24 gram 5.08 + 0.7 0.2 13Min 1.3 0.2 15 0.3 0.5 2.4 PIN 1 CASE PIN 2 + Case Negative Suffix"R" PIN 1 CASE PIN 2 CasePositive + Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25E ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current 0.375"(9.5mm) lead length @ at TA=100E Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum instantaneous forward voltage at 8.0A Maximum DC reverse current at rated DC blocking voltage TA=25E Maximum DC reverse current at rated DC blocking voltage TA=125E Maximum reverse recovery time (Note 1) Typical junction capacitance (Note 2) Typical thermal resistance (Note 3) Operating junction and storage temperature range IR VRRM VRMS VDC I(AV) IFSM VF HEP 801 50 35 50 HEP 802 100 70 100 HEP 803 200 140 200 8.0 125 1.0 10.0 HEP 804 300 210 300 HEP 805 400 280 400 HEP 806 600 420 600 Units Volts Volts Volts Amps Amps 1.3 1.7 Volts i A 100 Trr CJ 50 80 2.2 -55 to +150 -55 to +150 80 50 ns pF E /W E ReJC TJ TSTG Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. (3) Thermal resistance from junction to case mounting on heatsink. RATINGS AND CHARACTERISTIC CURVES HEP801 THRU HEP806 FIG . 1 -REVERSE RECOVERY TIME CHARACTERISTIC NONINDUCTIVE AND TEST CIRCUIT DIAGRAM 50 NONINDUCTIVE 10 +0.5A PULSE GENERATOR ( NOTE 2 ) 0 -0.25A DUT (+ ) 50Vdc (approx) (-) NONINDUCTIVE OSCILLOSCOPE (NOTE 2 ) -1.0A SET TIME BASE FOR 5/ 10ns / cm NOTES: 1 . RISE TIME = 7nsmax. INPUT IMPEDANCE= 1 MEGOHM 22p 2 . RISE TIME = 10ns max. SOURSE IMPEDANCE = 50ohmsf AVERAGE FORWARD CURRENT . ( A ) . FIG 2 -MAXIMUM AVERAGE FORWARD CURRENT DERATING 20 16 12 8 4 0 0 50 CASE TEMPERATURE . ( % ) 100 150 A) FIG . 3 -TYPICAL REVERSE CHARACTERISTICS 1000 INSTANTAN EOUS REVERSE CURRET . ( 100 Tj=125 C O 10 Tj=25 C O PEAK FORWARD SURGE CURRENT . ( A ) FIG . 4 -MAXIMUM NON - REPETITIVE FORWARD SURGE CURRENT 150 120 90 60 1 8.3ms Single Half Sine Wave JEDEC Method 0.1 0 PERCENT OF RATED PEAK REVERSE VOLT AGE . (%) 20 40 60 80 100 120 140 INSTANTANEOUS FORWARD CURRENT . ( A) 30 1 2 5 10 20 NMBER OF CYCLES AT 60Hz 50 100 FIG . 6 -TYPICAL FRWARD CHARACTERISTICS 100 30 EP 1.0 0.3 0.1 0.03 .01 .4 .6 .8 80 -H HE P8 10 3.0 4 FIG . 5 -TYPICAL JUNCTIOON CAP ACITANCE CAPACITANCE ( pF) 150 120 90 60 30 0 1 2 5 HE P8 06 HE HE P8 06 HEP 80 1 -HEP 805 01 P8 05 10 20 50 100 200 REVERSE VOLTAGE . ( V) 500 1.0 1.2 1.4 1.6 1.8 FORWARD VOLTAGE . ( V ) |
Price & Availability of HEP801
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |